Difference between revisions of "Front Axle/Differential R&R"
(Front Axle/Differential R&R moved to Grm: why not) |
1985amceagle (Talk | contribs) |
||
| Line 1: | Line 1: | ||
| − | + | 1980-1983 AMC Eagle's | |
| + | |||
| + | Differential repair requires special skills and specialty tools. | ||
| + | |||
| + | Inspection procedures found elsewhere in the AMC Eaglepedia will tell if repairs are necessary. | ||
| + | |||
| + | <center>'''Front Axle Differetial/Removal/Installation:'''</center> | ||
| + | |||
| + | http://img.photobucket.com/albums/v198/Gilspix/AMC%20Diagrams/Differentialfigure10.jpg | ||
| + | |||
| + | |||
| + | http://img.photobucket.com/albums/v198/Gilspix/AMC%20Diagrams/Differentialfigure11.jpg | ||
| + | |||
| + | 1.- Remove the axle assembly. | ||
| + | |||
| + | 2.- Remove the axle housing cover bolts and cover. | ||
| + | |||
| + | 3.- Mark the differential bearing caps with a centerpunch for reassembly alignment reference. | ||
| + | |||
| + | 4.- Loosen but do not remove the fiferential bearing cap bolts. | ||
| + | |||
| + | 5.- Install an axle housing spreader (tool part No. J-24385-01) and spreader adapters (toll part No. J-24161) as shown in <b>Figure 23.</b> Used hold-down clamps to keep spreader in position. | ||
| + | |||
| + | 6.- Install a dial indicator as shown in <b>Figure 23.</b> Zero the indicator gauge. make sure the indicator plunger touches one side of the housing opening | ||
| + | |||
| + | |||
| + | http://img.photobucket.com/albums/v198/Gilspix/AMC%20Diagrams/Differentialfigure23.jpg | ||
| + | |||
| + | <center>'''CAUTION: Do not exceed the specified housing spread in Step 7.''' | ||
| + | |||
| + | '''Spreading the housing greater amount than specified can cause damage or distortion.''' | ||
| + | </center> | ||
| + | |||
| + | |||
| + | 7.- Slowly spread the housing 0.020 in. (0.50 mm) while watching the indicator. Remove the dial indicator when housing spread is complete. | ||
| + | |||
| + | 8.- Remove and tag the differential bearing caps for reassembly reference. | ||
| + | |||
| + | 9.- Position one pry bar under the ring gear bolt head and a second pry bar under the differential case. remove the differential assembly from the housing. | ||
| + | |||
| + | 10.- Remove the spreader tool to prevent the possibility of housing distortion. | ||
| + | |||
| + | 11.- Installation is the reverse of removal. Tighten all fasteners to specifications. | ||
| + | |||
| + | |||
| + | http://img.photobucket.com/albums/v198/Gilspix/AMC%20Diagrams/Differentialtable1.jpg | ||
Latest revision as of 22:36, 29 April 2013
1980-1983 AMC Eagle's
Differential repair requires special skills and specialty tools.
Inspection procedures found elsewhere in the AMC Eaglepedia will tell if repairs are necessary.
http://img.photobucket.com/albums/v198/Gilspix/AMC%20Diagrams/Differentialfigure10.jpg
http://img.photobucket.com/albums/v198/Gilspix/AMC%20Diagrams/Differentialfigure11.jpg
1.- Remove the axle assembly.
2.- Remove the axle housing cover bolts and cover.
3.- Mark the differential bearing caps with a centerpunch for reassembly alignment reference.
4.- Loosen but do not remove the fiferential bearing cap bolts.
5.- Install an axle housing spreader (tool part No. J-24385-01) and spreader adapters (toll part No. J-24161) as shown in Figure 23. Used hold-down clamps to keep spreader in position.
6.- Install a dial indicator as shown in Figure 23. Zero the indicator gauge. make sure the indicator plunger touches one side of the housing opening
http://img.photobucket.com/albums/v198/Gilspix/AMC%20Diagrams/Differentialfigure23.jpg
Spreading the housing greater amount than specified can cause damage or distortion.
7.- Slowly spread the housing 0.020 in. (0.50 mm) while watching the indicator. Remove the dial indicator when housing spread is complete.
8.- Remove and tag the differential bearing caps for reassembly reference.
9.- Position one pry bar under the ring gear bolt head and a second pry bar under the differential case. remove the differential assembly from the housing.
10.- Remove the spreader tool to prevent the possibility of housing distortion.
11.- Installation is the reverse of removal. Tighten all fasteners to specifications.
http://img.photobucket.com/albums/v198/Gilspix/AMC%20Diagrams/Differentialtable1.jpg
